Wall with AluStarTec

AluStarTec wall formwork is a robust multi-purpose system covering large forming areas and heights up to 3.30 m. The system is compatible with the light-weight AluStarTec aluminium panels.

Scroll down this page to finde the components that you will need when formwing a wall with AluStarTec. Note that each building project will vary in terms of the number of parts needed. If you need assistance in planning the pour, please consult with us via the contact form.

You will find additional information on the AluStarTec system on the product page.

Contact Form

 
 
 

References AluStarTec

  • Bridge Building for beltway M 0 in Budapest/Hungary

    A simple, sophisticated design featuring few components and time-saving details distinguishes the MEP Shoring System, which consists of only three parts and, yet, is versatilely applicable: as single prop, slab table or shoring structure.

  • Bjørvika Reshapes Oslo Skyline

    The leading Norwegian concrete contractor BundeBygg AS, chose MEVA for all concrete works, including cores, elevator and staircase shafts, inside and outside walls, columns and slabs.

  • Waterway Crossing, Minden

    MEVA wall formwork Mammut was chosen because of its load capacity of 100 k/N/m².

 

Product List

 
 
Formwork
Ties
Bracing
Safety
 
 
  • ST panels

    Construction height 12 cm, frame profile width 4 cm. Three tie holes per panel height 330 cm, two tie holes per panel height... 

  • ST panel 270/45 with concreting window

    Is used to control the pouring process when control is not possible from above. 

  • ST panel AL 17, 270/45 with filling nozzle

    Is used when concrete cannot be poured from above, e.g. tunnel formwork. Connection with a manual gate valve. Operating... 

  • ST inside corner

    For 90° corners. Side length 25 cm. Steel frame with tie holes and alkus facing or exchangeable steel sheet. 

  • AS/ST outside corner

    Aluminium. Provides together with ST panels and AS assembly locks a fast and stable outside corner assembly for 90° angles. 

  • AS hinged inside corner

    Steel construction with steel sheeting. Side length 30 cm. Adjustable angle 60°-180°. 

  • AS hinged outside corner

    Steel construction with steel sheeting. Side length 7,5 cm. Adjustable angle 60°-180°. 

  • ST stripping corner

    Steel construction with steel sheeting. Side length 25 cm. With tie holes. When the bell-crank lever is pushed upwards with... 

  • Stripping support

    The stripping support is used to easily activate the stripping corner from above. Use a power screwdriver, a ratchet wrench... 

  • AS assembly lock

    Galvanized. Tightly connects and aligns AluStar and StarTec panels. Clamping length 8 cm.  

  • Uni-assembly lock

    Galvanized. For stepless compensation. Clamping length 22 cm or 28 cm. 

  • Combi-lock with coupling

    Galvanized. Is used to attach the push-pull props at the panel joint of the wall formwork AluStar, StarTec, Mammut and... 

  • Flange screw

    Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc.... 

  • ST aluminium filler

    Aluminium with high-quality annealed powder coating. With tie holes. For length compensation of 5 cm, especially in corners.... 

  • ST compensation plate

    Steel construction with steel sheeting. Is used to compensate gaps of 8 to 20 cm and attached to the panel with 2 assembly... 

  • AS timber profile

    Timber profile with groove. To support job-built fillers of 14 cm or more or to connect job-built formwork with 21 mm... 

  • Alignment rail

    Galvanized. Is used to brace panel joints for crane ganging, bridge problem areas, brace compensation areas and build stop... 

  • Stop end bracket

    Galvanized. Is used to form stop ends. Suitable for frame profile widths 23 mm (EcoAs, AluFix), 40 mm (AluStar, StarTec)... 

  • Uni-tie claw

    Galvanized. Permits tieing directly above or beside the panels. Is suited for panels with a frame profile width of 40 mm... 

  • Stop end fixture 23/40 yellow

    Yellow chromated. Is used to attach alignment rails to the panels when forming stop ends are formed. Or is used in... 

  • Door spindle MFS

    Steel, galvanized, DW 20. Adjustment range 700-1100 mm. Is used to brace door and window blockouts. With nail holes.... 

  • AS crane hook

    Is used to move panels. Self-locking. Load capacity: 15 kN (1,5 tons). Always 2 crane hooks required per gang. For use and... 

  • MevaTrenn pro

    Not shown. Suited for absorbent and non-absorbent forming faces.Solvent-based. Evaporates when applied, leaving avery thin... 

  • Sprayer

    Not shown. To allow for an even and sparing spraying of the forming surface, suited for (5 litre) MevaTrenn and wax. 

  • Concrete scraper

    With 6 or 10 replaceable hard-metal plates and steel ledge. Wooden stick (ash-tree) with handle. 

  • Beam clamp H20/H20

    Galvanized. Is used to attach planks or cross beams to H20 beams when using slab tables. 

  • Safety bolt

    Secures stacked panels. 

  • Transport angle 12

    Is used to stack and transport 5 to 12 frame formwork panels with a construction height of 12 cm and 12 cm hole distance.... 

 
 
  • Articulated flange nut 15/120

    Forged, galvanized. DIN 18216. DW thread Ø 15 mm, plate Ø 120 mm, max. inclination 10°, SW 27. Max. load capacity 90 kN.... 

  • Flange nut 100

    Forged, galvanized. DIN 18216. DW thread Ø 15 mm, plate Ø 100 mm, SW 27. Admissible load 90 kN. 

  • Spanner SW 27

    Inset yellow chromated. Spanner width (SW) 27 mm. Is used to tighten and loosen flange nuts 100, articulated flange nuts... 

  • Drive nut 60

    Galvanized. DIN 18216. DW thread Ø 15mm, plate Ø 60 mm. Adm. load capacity 90 kN. Is used to anchor the formwork to the... 

  • Tie rod DW 15/90

    Uncoated, not weldable. DW thread Ø 15 mm. Is used to tie panels of double-sided formwork. Adm. load capacity 90 kN (DIN... 

  • Pressure gauge

    Not shown. Measures tractive force of anchors from 250 to 400 kN. Includes compensating plate for tie rods, with 50 mm hole... 

  • Plug D20

    Is used to close unused tie holes (AluFix, EcoAs, AluStar and StarTec). 

  • Stop end bracket

    Galvanized. Is used to form stop ends. Suitable for frame profile widths 23 mm (EcoAs, AluFix), 40 mm (AluStar, StarTec)... 

  • Cone for plastic tube

    Available with 10 mm or 30 mm covering . 

  • Plug

    Is used to close tie holes in the wall when plastic tubes D22 or D30 are applied. Two plugs are required per tie hole.  

  • Water stop

    Uncoated. Lost part for tie rods DW 15 and DW 20 to produce watertight tie holes. Adm. load capacity depends on diameter: Ø... 

  • Uni-tie claw

    Galvanized. Permits tieing directly above or beside the panels. Is suited for panels with a frame profile width of 40 mm... 

  • Tensioner AS/ST for foundation tape

    Galvanized. Connects the foundation tape to AluStar or StarTec panels and serves as bottom anchoring when panels are... 

  • Trolley for foundation tape

    Not shown. Is used to transport and cut foundation tapes to length. Suitable for one roll Pneumatic wheels. 

  • Pressure gauge

    Not shown. Measures tractive force of anchors from 250 to 400 kN. Includes compensating plate for tie rods, with 50 mm hole... 

 
 
  • Side railing

    Galvanized. Is plugged into the walkway bracket. 

  • Push-pull prop R

    Galvanized. Garantee tensile and compression strength. Align and brace wall formwork. Foot plates and... 

  • Braces SRL

    Galvanized. Guarantee tensile and compression strength. With right-hand and left-hand spindle and revolving centre part.... 

  • Brace frame 250

    Galvanized. Aligns and braces the formwork. Available with or without formwork-prop connector. Consists of a push-pull prop... 

  • Ladder

    Galvanized. Is hooked into the CF-access platform and automatically secured. Can be extended with extension ladders. Safety... 

  • Formwork-prop connector

    Galvanized. Connects braces, brace frames and push-pull props (max. Ø 48 mm) to the multi-function profile (with a flange... 

  • Universal joint connector 76/135

    Galvanized. With head bolt 16/90 and cotter pin 4. Is used to attach push-pull props to vertical or horizontal panel joints... 

  • Articulated foot plate

    Galvanized. With head bolt 16/90 and cotter pin 4. For push-pull props and braces of up to Ø 57 mm. 

  • Double-jointed foot plate

    Galvanized. With head bolt 16/90 and cotter pin 4. Serves as foot plate for brace frames 250 and as connector for braces and... 

  • Formwork-prop connector

    Galvanized. Is used to connect braces, brace frames and push-pull props (max. Ø 48,3 mm) to the multi-function profile with... 

  • Flange screw

    Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc.... 

  • Triplex R

    Galvanized. Braces and aligns wall and column formwork exceeding 6,00 m. Is delivered in modules and assembled on site to... 

  • Triplex intermediate pieces R

    Galvanized basic components of different lengths to build Triplex R units. Tube Ø 33,7 mm. Delivery includes the required... 

  • Top unit 48

    Galvanized. With adjustable spindle (Ø 48,3 mm). 1 top unit 48 left and 1 top unit 48 right are required to assemble a... 

  • Foot plate 48

    Galvanized. Particularly solid foot plate for braces up to Ø 48,3 mm such as Triplex R. Delivery includes head bolt 16/90... 

  • Triplex SB

    Galvanized. Triplex SB braces are primarily used for additional load transfer when forming single-sided walls of 6,00 m or... 

  • Foot plate 73

    Galvanized. Particularly sturdy foot plate for Triplex SB. Delivery includes screw M30x150 and nut M30. 

  • Flange screw

    Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc.... 

  • Combi-lock with coupling

    Galvanized. Is used to attach push-pull props at the panel joints of AluStar, StarTec, Mammut and Mammut 350 wall formwork.... 

Worker protection is mandatory by law from a working height of 2 m. The working platform must be equippped with fall protection on all four sides.

MEVA safety systems offer you a flexible answer to safety requirements, compiled individiually to meet your project needs. Refer to the safety systems page and consult with us on the most effective and cost-efficient solution. 

  • Guard-railing post

    Galvanized. Is plugged into the walkway bracket. 

  • Guard-railing post 48

    Galvanized. With manifold to attach it to the walkway bracket, designed with tube Ø 48 mm to attach tube couplers. 

  • Support guard 800-railing post

    Galvanized. For the side protection at all MEVA wall formwork systems. Allows the extension for guard-railing KLK 230 and... 

  • Scaffold tube

    Galvanized. Is used as hand-rail / mid-rail in combination with guard-railing post 48. 

  • Plastic tube

    Is used as a plastic sleeve for a tie rod that is to be recovered and re-used. 2 m long.  

  • Planing cap DW

    Hard foam, 10 cm long, 45° end piece. For DW 15 and DW 20. Is plugged onto the DW tie rod or on a plastic sleeve for... 

  • Spiral anchor DW 15/100

    Steel spiral bead, 10 cm long, with styropore core. Is used to attach formwork equipment with tie rods DW 15, e.g. when... 

  • Folding access platform BKB 125

    Self-locking; ready-made platform with a foldable guard-railing and an overall width of 125 cm; it is supsended onto the... 

  • Folding access platform BKB 125/140

    It is used for inside corner configurations and length adjustments. In the latter case a side railing BKB 125 and two (2)... 

  • Side railing BKB 125

    Galvanized. Suited as side railing for all folding access platforms or as guard-railing for platform BKB 125/140. Is... 

  • Walkway bracket

    Galvanized, yellow, pluggable. Is used as a working and safety scaffold. Is attached to the multi-function profile and... 

  • Side railing

    Galvanized. Is plugged into the walkway bracket. 

  • Walkway bracket SB

    Galvanized. Is attached with 1 flange screw 28 and 1 flange screw 18 to the DW-threaded nuts of the panel’s multi-function... 

  • Walkway bracket 880 SB

    Galvanized. Is attached with 1 flange screw 28 and 1 flange screw 18 to the DW-threaded nuts of the panel’s multi-function... 

  • Alu(minium) platform ST SB

    Aluminium support construction with slip-free corrugated aluminium sheet. Working width 75 cm. Admissible load 200 kg/m².... 

  • Alu(minium) platform ST 2370 SB with hatch

    Aluminium support construction with slip-free corrugated aluminium sheet. Working width 75 cm. Admissible load 200 kg/m².... 

  • Alu platform outside corners SB

    Aluminium support construction with slip-free corrugated aluminium sheet. Is placed onto 2 Walkway brackets SB and on the... 

  • Protection bracket SB

    The protection bracket SB is plugged into the aluminium platform and attached to the wooden compensation platform with two... 

  • Compensation sheet

    Bridges gaps up to 135 cm of 75 cm wide. 

  • Compensation covering 570 plugable

    Pluggable. Bridges gaps up to 40 cm wide. 

  • Front guard-railing post SB 10

    Not shown. Galvanized. Is used together with a scaffold tube to create a handrail. The front guard-railing post SB 10 is... 

  • Front railing post SB retractable

    Galvanized, dia. 48.3 mm. Is used to install a retractable front railing SB made of scaffold tubes. On the facing side of... 

  • Support railing post SB, retractable

    Galvanized. Is used for the retractable front railing SB made of scaffold tubes. The support is attached to the walkway... 

  • Support for guard-railing post IC SB

    Galvanized. Is used for the attachment of a front guard-railing post. Is attached to the multi-function profile of the wall... 

  • Support for guard-railing post OC SB

    Galvanized. Is placed onto 2 Walkway brackets SB and secured to the Alu platform outside corners SB with the integrated pin. 

  • Scaffold tube SB

    Galvanized. Is used to assemble front railings for SecuritBasic aluminium platforms.  

  • Swivel-joint coupler 48/48

    Galvanized. Connects 2 scaffold tubes with 48,3 mm Ø at any angle.