Fall-down protection at slab edges

Fall-down protection at slab edgeszoom

Railing clamps, toe boards and handrails can be used to install a fall-down protection at the slab edge. 

Another option is to attach a guard-railing post support at the MevaDec panel or primary beam, plug the guard railing post into the support and attach the guard railing to the railing posts. 

We recommend using the MEVA MFS safety mesh rather than toe boards and handrails. 




MevaDec product page

MevaDec product page

Contact Form


Product List


Note that each building project will vary in terms of the number of parts needed. If you need assistance in planning the pour, please consult with us via the contact form.

  • EuMax 30

    Galvanized. According to European Standard EN 1065, class E. Admissible load capacity 30 kN. Higher load capacities are... 

  • MEP prop with SAS

    Combination of steel inner tube and aluminium outer tube with T-groove to attach reinforcing frames. The SAS quick lowering... 

  • EuMax 20

    Galvanized. According to the European Standard EN 1065 class D the admissible load capacity is 20 kN at any extension.... 

  • Forked prop head

    Galvanized. The forked prop head can be used as a support instead of a drop head at the beginning or end of a primary beam... 

  • Pin

    Galvanized. Is used to attach MD drop heads, MD prop heads of forked prop heads, etc. Pin 14/90 is used for steel tube props... 

  • Tripod

    Galvanized auxiliary to stabilize props with Ø 48 to 80 mm. The turnable legs allow the tripod to be used in rooms, along... 

  • Accessories for attachment

    Are used to attach MD drop heads and MD prop heads to the MD/ME props.  

  • Shuttering panel 3S

    Three-layer plywood forming face, 21 mm thick, with resistant coating on both sides. Good pore structure of the concrete due... 

  • Shuttering panel 7S

    Not shown. Multi-layer plywood forming face, 21 mm thick, with film-coating on both sides and edge protection. 

  • Formwork girder H20

    Robust multi-purpose girder for the most different tasks. While the girder itself does not weigh much, it has a high... 

  • Connector Clip H20

    Galvanized. Is used to connect wooden H20 girders to each other. The wedge locks the girdes into place and releases them. 

Worker protection is mandatory by law from a working height of 2 m. The working platform must be equippped with fall protection on all four sides.

MEVA safety systems offer you a flexible answer to safety requirements, compiled individiually to meet your project needs. Refer to the safety systems page and consult with us on the most effective and cost-efficient solution. 

  • Guard-railing post

    Galvanized. Is plugged into the MD support for panel or beam. 

  • Guard-railing post 48

    Galvanized. With manifold to be plugged into the walkway bracket and with 48 mm Ø tube to attach scaffold couplers.  

  • MD support for guard-railing post / panel

    Galvanized. Permits attachment of a guard-railing post at the MD panels and is used to form a stop end at the edge of the... 

  • MD support for guard-railing post / beam

    Galvanized. Permits attachment of a guard-railing post at primary and secondary beams and is used to form a stop end at the... 

  • Railing clamp

    Coated. Is used as side railing at the slab edge and can be clamped to all kinds of beams or concrete slabs. Railing clamp... 

  • Scaffold tube

    Galvanized. Is used as hand-rail / mid-rail in combination with guard-railing post 48. 

  • Swivel-joint coupler 48/48

    Galvanized. Connects 2 scaffold tubes with Ø 48,3 mm at any angle required. 

  • Safety mesh

    Steel, painted. Sturdy steel mesh with reinforced edges and closed steel sheet to prevent small items from falling down. The... 

  • Safety mesh extension

    Steel, painted. Height extension for safety mesh MFS. 500 kg impact protection. Meets the requirements as defined by... 

  • Safety mesh corner hinge

    Steel, galvanized. Connects safety meshes MFS at angles from 76° to 284°. Can be attached anywhere at the safety mesh. 

  • Stop-end rail MFS

    Steel, galvanized. Is used to form slab ends for slabs up to 60 cm thick. 

All Plastic Facing alkus
MEVA Frame Profile
... more than just formwork
  •  Select language

    Select continent and country. Language selection optional.

  •  Contact
  •  Search

    Search on our website.

  •  Newsletter

    Subscribe to our monthly newsletter.